Growing Environment

Can-Filters® has designed and built the Can-Lite™ for convenience and long life. 100% Australian granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 7 sizes with a CFM range of 89 to 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

• Monitors air temperature, relative humidity, VPD, and ambient CO₂ levels.
• Provides accurate VPD calculations with precise temperature and humidity data.
• Samples ambient CO₂ five times per minute for precise CO₂ control.
• Integrates with the AROYA app for automatic data syncing every three minutes.
• Easy installation with included pulley system and hanging hooks.
• Rugged construction for durability in demanding grow environments.
• Wireless BLE mesh network connectivity for reliable data transmission.
• 48V PoE power supply with 3W peak consumption.
• Trade-in discount of 25% for upgrading from an old AROYA climate station.
• Measures temperature (-10 to 50 °C) and CO₂ (0 to 2,000 ppm) with high accuracy.

The Max-Fan® is the first fan that has been developed with a Computational Fluid Dynamics (CFD) program. CFDs are used for engineering aircraft propulsion engines. The perfectly designed 3D blades of the impeller and stator make this fan extremely powerful and energy efficient. Compared with other inline fans, the efficiency is 50% to 100% higher. 6 inch to 14 inch come pre-wired with an 8 foot 120 V power cord. Can-Fan® bring its innovation to market and sets a new standard for performance. The Max-Fan is a more powerful and efficient fan that takes less energy to run.

@ 80°F | 60% RH

• Water removal: 730 pints | 345 liters | 91.3 gallons
• Efficiency: 8.3 pints/kWh
• Supply voltage: 480 V, 3 phase, 60 Hz
• Amps: 4.9
• Energy factor: 3.9 L/kWh
• Operating temp: 56°F min – 95°F max
• Air filter: MERV-13 (Qty 2)
• Dimensions (L x W x H): 44.8 x 28.9 x 27.4 in (113.8 x 73.4 x 69.6 cm)

The Ideal-Air™ Pro Series Ultra Sonic Humidifier is designed with ultra-sonic transducers to supply ultra-fine water particles. This is to help form a more balanced humidity field over your plant's entire canopy. Ideal-Air™ Pro Series Ultra Sonic Humidifier plates are made from cold-rolled steel and a stainless steel box with a standard water inlet with overflow safety switch, reservoir drain outlet, sediment filter, LED display and humidity control (30%–90%). This unit is designed to produce up to 150 pints per day of ultra-fine mist. 115 V, 60 Hz and 2.7 Amps. We recommend all Ultra Sonic Humidifiers be ducted, using 4 in PVC or 4 in DWV plastic pipe works best. Units should not be run without ducting or the top of the unit may be covered in water and shut off. Please don’t fill the unit through the discharge piping outlets. Doing this will overfill the tank and prevent the unit from creating humidity. The unit should only be filled through the provided hose and float valve to ensure proper water level and correct operation.

Can-Filter® has designed and built the Can-Lite™ for convenience and long life. 100% Australian Granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 12 sizes with a CFM range of 89 - 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

Can-Filter® has designed and built the Can-Lite™ for convenience and long life. 100% Australian Granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 12 sizes with a CFM range of 89 - 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

The flange is used to connect the Can-Filter® to the ducting or Can-Fan®; this is for airflow out of the ventilated area. These spun steel flanges come with a foam rubber seal and 6 hex drive self-tapping screws forming a perfect seal with Can-Filter products. Flanges range in size from 4 in to 20 in depending on your specific needs.

Can-Filters® has designed and built the Can-Lite™ for convenience and long life. 100% Australian granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 7 sizes with a CFM range of 89 to 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

Very low air resistance, easily changed. MERV-5 mesh blocks pollen, dust and other particulate from entering filter. Available in sizes for all filters. A clean Can-Filter® Pre-Filter is an excellent way of extending the working life of your Can-Filter filter.

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 4 inches (10 centimeters).

The Ideal-Air™ Pro Series Ultra Sonic Humidifier is designed with ultra-sonic transducers to supply ultra-fine water particles. This is to help form a more balanced humidity field over your plant's entire canopy. Ideal-Air™ Pro Series Ultra Sonic Humidifier plates are made from cold-rolled steel and a stainless steel box with a standard water inlet with overflow safety switch, reservoir drain outlet, sediment filter, LED display and humidity control (30%–90%). This unit is designed to produce up to 150 pints per day of ultra-fine mist. 115 V, 60 Hz and 2.7 Amps. We recommend all Ultra Sonic Humidifiers be ducted, using 4 in PVC or 4 in DWV plastic pipe works best. Units should not be run without ducting or the top of the unit may be covered in water and shut off. Please don’t fill the unit through the discharge piping outlets. Doing this will overfill the tank and prevent the unit from creating humidity. The unit should only be filled through the provided hose and float valve to ensure proper water level and correct operation.

• Classic series oscillating wall mount fan.
• Designed for efficient air circulation in compact spaces.
• Ideal for growrooms, greenhouses, homes, garages, workshops, and more.
• Three turn-switch or pull-cord controlled speed settings.
• 90 degree lockable oscillation.
• Durable steel neck support.
• 5 foot (1.5 meter) power cord.
• cETL listed.
• 16 inch (40 centimeter) fan.

• Circulates 1,015 cubic feet of air per minute on only 1.1 amps.
• 1,015 CFM high velocity air flow thanks to the dual axial design.
• Daisy-chain and synchronize up to 10 Quest F10 fans on the same 15-amp circuit.
• Ensures optimal airflow and enhances dehumidifier performance.
• Engineered as two fans in one, with less power draw than its predecessor.
• Features designated mounting corners for multiple setup configurations.
• Sleek design fits into tight spaces, under plant canopies, or between tiered shelves.

• Specialized photobiology spectroradiometer from 380 to 780 nm.
• Small and lightweight, with a rugged housing and minimal moving parts.
• Self-powered to take measurements anywhere, and the unit can store measurements for dowloading to a PC later.
• Measurement of spectral output from radiation sources used for growing in greenhouses, growth chambers, etc.
• Measurement of solar spectra with changing atmospheric conditions.
• Measurement of spectral reflectance on stationary (e.g., agricultural or ecological weather stations and flux towers), and mobile (e.g., plant phenotyping) platforms.

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 8 inches (20 centimeters).

The Max-Fan® Pro Series is even more efficient and stronger than the original Max-Fan design. The Max-Fan Pro Series has a much more robust housing due to the fiberglass reinforced plastic compounds that meet all of the UL and CSA requirements. The fans have three control speeds for true performance. These fans run quieter than the Max-Fan. The fans come with the EZ Mount™ bracket for easy mounting.

Each Original Can-Filter® uses the most conceptually sound, granular carbon, packed-bed design to deliver the best performing carbon filter on the market. Even with the industry's thickest carbon bed, at 2.5 inches, the Can Original provides for some of the lowest pressure drops, even on smaller size filters. This hefty granular carbon bed effectively makes the Original filter the biggest sponge for VOC removal capable of holding massive amounts of contaminant leading to a lifespan that leaves other filters, frankly, in the dust. The Original Can-Filter are designed for the control of VOCs (paint fumes, hydrocarbons, etc...), odors and other gaseous contaminants. Built with the same proven packed bed design and granular virgin activated carbon we've used for 30 years, this line of time tested activated carbon air filters sets the standard for long life, consistent performance and low pressure drop. Rated at a conservative 0.1 sec contact time, the Original Can-Filter provide excellent value and confidence.

Temperature control range is 55°F to 95°F. Controls cooling or heating equipment. Day and night settings keep temperature within 4°F of set point. 6 ft temperature probe is accurate to within 2°F. Enclosure protects internal components from dust, rust and moisture. ETL listed for commercial applications. 15 Amps/ 120 V/ 60 Hz.

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 6 inches (15 centimeters).

Can-Filters® has designed and built the Can-Lite™ for convenience and long life. 100% Australian granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 7 sizes with a CFM range of 89 to 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

Can-Filters® has designed and built the Can-Lite™ for convenience and long life. 100% Australian granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 7 sizes with a CFM range of 89 to 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

"The Ideal-Air Dehumidifiers are now rated at AHAM standards (80°F, 60% Relative Humidity). There is no change to the unit itself, only to the temperature and humidity at which the reading is being taken from. Previously they were rated at a higher temperature and humidity level based on hydroponic industry standard usage (86°F, 80% Relative Humidity). They will now be rated at AHAM standards based on the recent US Department of Energy ruling. Rated at 120 pints per day at 86°F/80% RH, now rated 60 Pint @ 80°F, 60% RH Quick maintenance with easy filter access that is removable and washable. Low temperature defrosting. Easy to move with built-in handles and wheels. Features a LED display panel. Removable water tank with an automatic shutoff when the reservoir is full. Internal condensate pump for easy water disposal. Can also be plumbed for permanent drainage. Tank reservoir capacity is 10 liters or 21 pints. 7 Amps/680 W/271 CFM. 115 V."

• High-capacity dehumidification: Designed for areas needing higher-capacity equipment to eliminate condensation and related safety hazards.
• Flexible water removal: Features an internal condensate pump capable of lifting and moving water up to 17 feet vertically and 30 feet horizontally.
• User-friendly controls: Equipped with an onboard digital dehumidistat adjustable from 20 to 80% RH, with positive "On" and "Off" settings.

@ 80 F / 60% RH

• Capacity: 195 Pints/Day
• Efficiency: 6.1 Pints/kWh
• Supply Voltage: 115 V
• Current Draw: 12 Amps

The Max-Fan® Pro Series is even more efficient and stronger than the original Max-Fan design. The Max-Fan Pro Series has a much more robust housing due to the fiberglass reinforced plastic compounds that meet all of the UL and CSA requirements. The fans have three control speeds for true performance. These fans run quieter than the Max-Fan. The fans come with the EZ Mount™ bracket for easy mounting.

The Max-Fan® is the first fan that has been developed with a Computational Fluid Dynamics (CFD) program. CFDs are used for engineering aircraft propulsion engines. The perfectly designed 3D blades of the impeller and stator make this fan extremely powerful and energy efficient. Compared with other inline fans, the efficiency is 50% to 100% higher. 6 inch to 14 inch come pre-wired with an 8 foot 120 V power cord. Can-Fan® bring its innovation to market and sets a new standard for performance. The Max-Fan is a more powerful and efficient fan that takes less energy to run.