Greenhouses, Grow Tents, & Systems

Quick maintenance with easy filter access that is removable and washable. Low temperature defrosting. Easy to move with built-in handles and wheels. Easy-to-use LED display panel. Removable water tank with an automatic shutoff when reservoir is full. The reservoir for the dehumidifiers is 6 liters or 12.5 pints. 22 pint is 4.0 Amps/420 W. 30 pint is 4.7 Amps/520 W. 50 Pint is 6.9 Amps/720 W. 115 V. Can be plumbed for permanent drainage.

Quick maintenance with easy filter access that is removable and washable. Low temperature defrosting. Easy to move with built-in handles and wheels. Features a LED display panel. Removable water tank with an automatic shutoff when reservoir is full. Internal condensate pump for easy water disposal. Can also be plumbed for permanent drainage. Tank reservoir capacity is 10 liters or 21 pints. 7 Amps/680 W/271 CFM. 115 V.

Ideal-Air™ Pro Series 100 Pint Dehumidifier has automatic restart if power is lost. Easy-to-use digital display humidity readings, internal condensate pump, removable washable filter, 1 speed fan motor, powder-coated metal casing for long life and a heavy-duty compressor. Built-in defrost that is designed for operation down to 41°F. Set upright on their feet for 3 hrs prior to use. 100 pint unit: Temp. Range: 41°F–95°F, condensation removal: (24 hrs) 100 pints (86°F, 80% RH); Power: 6.75 Amps/728 W; Supply Voltage: 115 V - 1 Phase - 60 Hz; R410A. Ideal-Air recommends that dehumidifiers use surge protectors and a dedicated electrical circuit. In the event of a power failure, a spike in voltage may occur when the power is reinstated. This can damage the circuit board, which is not covered under warranty.

Ideal-Air™ Pro Series 180 Pint Dehumidifier has automatic restart if power is lost. Easy-to-use digital display humidity readings, internal condensate pump, removable washable filter, 1 speed fan motor, powder-coated metal casing for long life and a heavy-duty compressor. Built-in defrost that is designed for operation down to 41°F. Set upright on their feet for 3 hrs prior to use. 180 pint unit: Temp. Range: 41°F–95°F, condensation removal: (24 hrs) 180 pints (86°F, 80% RH); Power: 12.31 Amps/1350 W; Supply Voltage: 115 V - 1 Phase - 60 Hz; R410A. Ideal-Air™ recommends that dehumidifiers use surge protectors and a dedicated electrical circuit. In the event of a power failure, a spike in voltage may occur when the power is reinstated. This can damage the circuit board, which is not covered under warranty.

The Ideal-Air™ Pro Series Ultra Sonic Humidifier is designed with ultra-sonic transducers to supply ultra-fine water particles. This is to help form a more balanced humidity field over your plant's entire canopy. Ideal-Air™ Pro Series Ultra Sonic Humidifier plates are made from cold-rolled steel and a stainless steel box with a standard water inlet with overflow safety switch, reservoir drain outlet, sediment filter, LED display and humidity control (30%–90%). This unit is designed to produce up to 150 pints per day of ultra-fine mist. 115 V, 60 Hz and 2.7 Amps. We recommend all Ultra Sonic Humidifiers be ducted, using 4 in PVC or 4 in DWV plastic pipe works best. Units should not be run without ducting or the top of the unit may be covered in water and shut off. Please don’t fill the unit through the discharge piping outlets. Doing this will overfill the tank and prevent the unit from creating humidity. The unit should only be filled through the provided hose and float valve to ensure proper water level and correct operation.

The Ideal-Air™ Pro Series Ultra Sonic Humidifier is designed with ultra-sonic transducers to supply ultra-fine water particles. This is to help form a more balanced humidity field over your plant's entire canopy. Ideal-Air™ Pro Series Ultra Sonic Humidifier plates are made from cold-rolled steel and a stainless steel box with a standard water inlet with overflow safety switch, reservoir drain outlet, sediment filter, LED display and humidity control (30%–90%). This unit is designed to produce up to 300 pints per day of ultra-fine mist. 115 V, 60 Hz and 7.8 Amps. We recommend all Ultra Sonic Humidifiers be ducted, using 4 in PVC or 4 in DWV plastic pipe works best. Units should not be run without ducting or the top of the unit may be covered in water and shut off. Please don’t fill the unit through the discharge piping outlets. Doing this will overfill the tank and prevent the unit from creating humidity. The unit should only be filled through the provided hose and float valve to ensure proper water level and correct operation.

The Ideal-Air™ Pro Series Ultra Sonic Humidifier is designed with ultra-sonic transducers to supply ultra-fine water particles. This is to help form a more balanced humidity field over your plant's entire canopy. Ideal-Air™ Pro Series Ultra Sonic Humidifier plates are made from cold-rolled steel and a stainless steel box with a standard water inlet with overflow safety switch, reservoir drain outlet, sediment filter, LED display and humidity control (30%–90%). This unit is designed to produce up to 600 pints per day of ultra-fine mist. 115 V, 60 Hz and 10.3 Amps. We recommend all Ultra Sonic Humidifiers be ducted, using 4 in PVC or 4 in DWV plastic pipe works best. Units should not be run without ducting or the top of the unit may be covered in water and shut off. Please don’t fill the unit through the discharge piping outlets. Doing this will overfill the tank and prevent the unit from creating humidity. The unit should only be filled through the provided hose and float valve to ensure proper water level and correct operation.

The Titan Controls™ Tali™ 3 in 1 VPD Sensor is designed to accurately measure the temperature, humidity, and air pressure of your growing environment. Using these readings, it will accurately calculate the VPD (vapor pressure deficit) for the monitored area. An easy-to-read LED screen allows you to quickly see what’s going on in your environment.

The Titan Controls™ Triton™ Standard Substrate Sensor is designed to accurately measure the EC (electrical conductivity), VWC (volumetric water content), and temperature of your substrate (growing media). Understanding these three metrics will allow you to optimize your irrigation strategy to realize your plants' full potential. The compact design allows this sensor to be easily installed in most applications.

• Ideal for residential, commercial, and industrial applications.
• Easy to install inline configuration, compatible with variable speed controllers.
• Designed to overcome resistance from long ducting; works with flexible and rigid ducting.
• Permanently lubricated for maintenance-free and continuous operation.
• Balanced fan and motor assembly for quiet, vibration-free performance.
• Features infinitely variable airflow with available 3-wire solid-state speed control.
• Suitable for light dust and fumes.
• Heavy-gauge, spun steel housing with baked epoxy finish inside and outside.
• Backward curved blades for low sound and ample static pressure.
• Durable external rotor motor with thermal reset overload protection.
• Pre-wired with 120-volt power cords.
• 4 in (10 cm) 152 CFM inline duct fan.

• High performance inline fans.
• Feature superior plastic or metal construction.
• Speed controllable.
• Vibration-free operation.
• Come with pre-installed cords from the manufacturer.
• Protected by a 1 year warranty.
• 10 in (25 cm) 780 CFM metal fan.

• High performance inline fans.
• Feature superior plastic or metal construction.
• Speed controllable.
• Vibration-free operation.
• Come with pre-installed cords from the manufacturer.
• Protected by a 1 year warranty.
• 12 in (30 cm) 1,060 CFM metal fan.

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 4 inches (10 centimeters).

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 6 inches (15 centimeters).

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 8 inches (20 centimeters).

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 10 inches (25 centimeters).

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Size: 12 inches (30 centimeters).

Can-Filter® has designed and built the Can-Lite™ for convenience and long life. 100% Australian Granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 12 sizes with a CFM range of 89 - 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

Can-Filter® has designed and built the Can-Lite™ for convenience and long life. 100% Australian Granulated carbon, aluminum top and bottom, integrated flange and 51% open perforation are features of the Can-Lite filter. The Can-Lite is available in 12 sizes with a CFM range of 89 - 3000. Can-Lite is manufactured in a dedicated carbon filter plant in North America. Each filter is shrink wrapped, boxed and labeled for ease of use.

The Max-Fan® is the first fan that has been developed with a Computational Fluid Dynamics (CFD) program. CFDs are used for engineering aircraft propulsion engines. The perfectly designed 3D blades of the impeller and stator make this fan extremely powerful and energy efficient. Compared with other inline fans, the efficiency is 50% to 100% higher. 6 inch to 14 inch come pre-wired with an 8 foot 120 V power cord. Can-Fan® bring its innovation to market and sets a new standard for performance. The Max-Fan is a more powerful and efficient fan that takes less energy to run.

The Max-Fan® is the first fan that has been developed with a Computational Fluid Dynamics (CFD) program. CFDs are used for engineering aircraft propulsion engines. The perfectly designed 3D blades of the impeller and stator make this fan extremely powerful and energy efficient. Compared with other inline fans, the efficiency is 50% to 100% higher. 6 inch to 14 inch come pre-wired with an 8 foot 120 V power cord. Can-Fan® bring its innovation to market and sets a new standard for performance. The Max-Fan is a more powerful and efficient fan that takes less energy to run.

The Max-Fan® Pro Series is even more efficient and stronger than the original Max-Fan design. The Max-Fan Pro Series has a much more robust housing due to the fiberglass reinforced plastic compounds that meet all of the UL and CSA requirements. The fans have three control speeds for true performance. These fans run quieter than the Max-Fan. The fans come with the EZ Mount™ bracket for easy mounting.

The Max-Fan® Pro Series is even more efficient and stronger than the original Max-Fan design. The Max-Fan Pro Series has a much more robust housing due to the fiberglass reinforced plastic compounds that meet all of the UL and CSA requirements. The fans have three control speeds for true performance. These fans run quieter than the Max-Fan. The fans come with the EZ Mount™ bracket for easy mounting.

The Max-Fan® Pro Series is even more efficient and stronger than the original Max-Fan design. The Max-Fan Pro Series has a much more robust housing due to the fiberglass reinforced plastic compounds that meet all of the UL and CSA requirements. The fans have three control speeds for true performance. These fans run quieter than the Max-Fan. The fans come with the EZ Mount™ bracket for easy mounting.

Controls and monitors CO₂ from 0 to 2,000 parts per million (PPM). CO₂ enrichment or CO₂ exhaust features. Easy to setup and operate. Enclosure resists dust, rust and moisture. 5 Amps maximum/120 V/ 60 Hz.