Ballasts & Electrical Components

• Includes the HR96 Reflector for maximum efficiency and uniformity.
• Designed with broad light dispersion in mind.
• Highly efficient passive ballast cooling for longer fixture life.
• Sealed housing with a Gore-Tex® ventilation plug.
• Controllable output up to 1,150 watts.
• Equipped with a dimming knob for manual light output adjustment.
• Features a Repeater Bus interface for control with a Gavita EL Controller (sold separately).
• Connect up to 100 fixtures in a single daisy chain series, up to five daisy chains per EL controller output.
• A single EL controller output can control up to five 100-fixture daisy chains.

• Double-ended light fixture.
• Optimized for low-ceiling rooms and greenhouses.
• Efficiency and uniformity guarantee over 95% light transmission to plants.
• Built-in spirit level ensures even light spread.
• Each light ray is either transmitted directly to plants or hits the aluminum reflector once.
• Output µmol/s: 2,100.
• Beam angle: 140° wide.
• Power: 1,000 watts.
• Voltage: 208 - 240 volts.

• Connects Gavita® EL3 Master controller to first Titan Controls® VPD Sensor or Titan Controls® Substrate Sensor.
• Products then daisy chain together after this first connection.

• DC extension cable for Fluence VYPR 4.
• Length: 6 feet (1.8 meters).

• UL approved magnetic ballast.
• Specialized switch for changing between MH and HPS bulbs.
• Switch between 120 V and 240 V power.
• 8-foot (2.4 m) 240 V power cord included.
• 120 V power cord available separately.
• No additional wiring needed.

• 1,000 watt magnetic ballast.
• Can easily switch between MH and HPS bulbs by flipping a specialized switch.
• Can also be switched between four primary input voltages: 120 V, 208 V, 240 V or 277 V.
• The aluminum housing is specially designed to dissipate heat and keep components cool.
• Top of the line Aerovox® capacitor is also included.
• Use the 120 V or 240 V power cord (sold separately) to change between these two voltages.
• If 208 V or 277 V operation is required the wiring must be changed by a certified electrician.
• The lamp cord receptacle accepts all LightEnerG™ lamp cords and reflectors.
• UL approved.

• 1,000 watt magnetic ballast.
• Can easily switch between MH and HPS bulbs by flipping a specialized switch.
• Also switchable between 120 V and 240 V.
• Use provided 120 V cord or 240 V cord (sold separately).
• No additional wiring is necessary.
• The aluminum housing dissipates heat and keeps components cool.
• Includes a top-of-the-line Aerovox® capacitor.
• Lamp cord receptacle accepts all LightEnerG lamp cords and reflectors.

• 400 watt magnetic ballast.
• Can easily switch between MH and HPS bulbs by flipping a specialized switch.
• Also switchable between 120 V and 240 V.
• Use provided 120 V cord or 240 V cord (sold separately).
• No additional wiring is necessary.
• The aluminum housing dissipates heat and keeps components cool.
• Includes a top-of-the-line Aerovox® capacitor.
• Lamp cord receptacle accepts all LightEnerG lamp cords and reflectors.

• Magnetic ballast capable of switching between 120 V and 240 V.
• Use either the 120v or a 240v power cord (sold separately) to change the voltage of the ballast.
• No additional wiring is necessary.
• Can also be used with 600 W MH conversion lamps.
• Aluminum housing is specially designed to dissipate heat and keep components cool.
• Includes a top-of-the-line Aerovox® capacitor.
• Lamp cord receptacle accepts all LightEnerG lamp cords and reflectors.

• Magnetic ballast capable of switching between 120 V and 240 V.
• Use either the 120v or a 240v power cord (sold separately) to change the voltage of the ballast.
• No additional wiring is necessary.
• Can also be used with 600 W MH conversion lamps.
• Aluminum housing is specially designed to dissipate heat and keep components cool.
• Includes a top-of-the-line Aerovox® capacitor.
• Lamp cord receptacle accepts all LightEnerG lamp cords and reflectors.

• Magnetic ballast features specialized switch to easily flip between MH and HPS lamps.
• Can run on 120 V or 240 V.
• Pre-assembled: No additional wiring is necessary.
• Galvanized steel construction.
• Top of the line Aerovox® capacitor included.
• Cord receptacle accepts all LightEnerG lamp cords and reflectors.
• Super duty handles.
• Rubber base supports for increased heat dissipation and noise dampening.
• Includes 15-foot (4.6-meter) lamp wire and 6-foot power cord (120 V).
• 240 V power cord sold separately.

• UL certified ballast unit.
• North American made capacitor.
• Quad-tap (120 V, 208 V, 240 V, and 277 V).
• Must be assembled by a qualified electrician.
• Only for use with HPS bulbs.

• UL certified ballast unit.
• North American made capacitor.
• Quad-tap (120 V, 208 V, 240 V, and 277 V).
• Must be assembled by a qualified electrician.
• Only for use with MH bulbs.

15 amp / 250 volt replacement fuse for The ACE™ Digital Ballast.

10 amp / 250 volt replacement fuse for The ACE™ Digital Ballast.

6.3 amp / 250 volt replacement fuse for The ACE™ Digital Ballast.

• State-of-the-art, UL-approved electronic ballast.
• Compatible with both MH and HPS bulbs.
• Features a dimmable switch with the ability to adjust watt output for three different settings.
• Has carefully arranged circuit boards and stainless steel ball bearing fans.
• Runs 15% cooler than standard ballasts, ensuring longer life and improved performance.
• Generator-ready with the most stable output frequency of any comparable ballast.
• Results in lower power loss and better overall power management.
• Has a power factor of 99.9% for 100% of the time.
• Far more efficient than older core and coil ballasts.
• Wattage: 1,000 W.

• State-of-the-art, UL-approved electronic ballast.
• Compatible with both MH and HPS bulbs.
• Features a dimmable switch with the ability to adjust watt output for three different settings.
• Has carefully arranged circuit boards and stainless steel ball bearing fans.
• Runs 15% cooler than standard ballasts, ensuring longer life and improved performance.
• Generator-ready with the most stable output frequency of any comparable ballast.
• Results in lower power loss and better overall power management.
• Has a power factor of 99.9% for 100% of the time.
• Far more efficient than older core and coil ballasts.
• Wattage: 600 W.

• State-of-the-art, UL-approved electronic ballast.
• Compatible with both MH and HPS bulbs.
• Features a dimmable switch with the ability to adjust watt output for three different settings.
• Has carefully arranged circuit boards and stainless steel ball bearing fans.
• Runs 15% cooler than standard ballasts, ensuring longer life and improved performance.
• Generator-ready with the most stable output frequency of any comparable ballast.
• Results in lower power loss and better overall power management.
• Has a power factor of 99.9% for 100% of the time.
• Far more efficient than older core and coil ballasts.
• Wattage: 400 W.

• 600 volt, 1,500 watt, 5kV pulse-rated porcelain mogul base sockets.
• Accommodate all mogul base bulbs in a universal position.
• Mogul cap and washer included.
• No lead.

• Used with HID ballasts to store energy.
• Delivers long life and high temperature operation.
• Made in North America.

• Used with HID Ballasts to store energy.
• Engineered for long life and high temperature operation.
• Made in North America.

• Insulates the capacitor terminals.
• Prevents nuisance shocks.

• Used with HID ballasts and capacitors to start HPS bulbs.
• Engineered for long life and high temperature operation.

• Used with HID ballasts and capacitors to start HPS bulbs.
• Engineered for long life and high temperature operation.