Growing Environment

Quick maintenance with easy filter access that is removable and washable. Low temperature defrosting. Easy to move with built-in handles and wheels. Easy-to-use LED display panel. Removable water tank with an automatic shutoff when reservoir is full. The reservoir for the dehumidifiers is 6 liters or 12.5 pints. 22 pint is 4.0 Amps/420 W. 30 pint is 4.7 Amps/520 W. 50 Pint is 6.9 Amps/720 W. 115 V. Can be plumbed for permanent drainage.

Ideal-Air™ Pro Series 180 Pint Dehumidifier has automatic restart if power is lost. Easy-to-use digital display humidity readings, internal condensate pump, removable washable filter, 1 speed fan motor, powder-coated metal casing for long life and a heavy-duty compressor. Built-in defrost that is designed for operation down to 41°F. Set upright on their feet for 3 hrs prior to use. 180 pint unit: Temp. Range: 41°F–95°F, condensation removal: (24 hrs) 180 pints (86°F, 80% RH); Power: 12.31 Amps/1350 W; Supply Voltage: 115 V - 1 Phase - 60 Hz; R410A. Ideal-Air™ recommends that dehumidifiers use surge protectors and a dedicated electrical circuit. In the event of a power failure, a spike in voltage may occur when the power is reinstated. This can damage the circuit board, which is not covered under warranty.

The Ideal-Air™ Pro Series Ultra Sonic Humidifier is designed with ultra-sonic transducers to supply ultra-fine water particles. This is to help form a more balanced humidity field over your plant's entire canopy. Ideal-Air™ Pro Series Ultra Sonic Humidifier plates are made from cold-rolled steel and a stainless steel box with a standard water inlet with overflow safety switch, reservoir drain outlet, sediment filter, LED display and humidity control (30%–90%). This unit is designed to produce up to 150 pints per day of ultra-fine mist. 115 V, 60 Hz and 2.7 Amps. We recommend all Ultra Sonic Humidifiers be ducted, using 4 in PVC or 4 in DWV plastic pipe works best. Units should not be run without ducting or the top of the unit may be covered in water and shut off. Please don’t fill the unit through the discharge piping outlets. Doing this will overfill the tank and prevent the unit from creating humidity. The unit should only be filled through the provided hose and float valve to ensure proper water level and correct operation.

The Titan Controls™ grow room sensors are designed for the grower in mind. For use with the Gavita™ EL3 Controller (sold separately and requires Titan Sensor Adapter Cable), they provide accurate environmental data and historical conditions that allow growers to further enhance and optimize their growing room.

The Titan Controls™ Tali™ 3 in 1 VPD Sensor is designed to accurately measure the temperature, humidity, and air pressure of your growing environment. Using these readings, it will accurately calculate the VPD (vapor pressure deficit) for the monitored area. An easy-to-read LED screen allows you to quickly see what’s going on in your environment.

The Titan Controls™ Triton™ Standard Substrate Sensor is designed to accurately measure the EC (electrical conductivity), VWC (volumetric water content), and temperature of your substrate (growing media). Understanding these three metrics will allow you to optimize your irrigation strategy to realize your plants' full potential. The compact design allows this sensor to be easily installed in most applications.

• Ideal for residential, commercial, and industrial applications.
• Easy to install inline configuration, compatible with variable speed controllers.
• Designed to overcome resistance from long ducting; works with flexible and rigid ducting.
• Permanently lubricated for maintenance-free and continuous operation.
• Balanced fan and motor assembly for quiet, vibration-free performance.
• Features infinitely variable airflow with available 3-wire solid-state speed control.
• Suitable for light dust and fumes.
• Heavy-gauge, spun steel housing with baked epoxy finish inside and outside.
• Backward curved blades for low sound and ample static pressure.
• Durable external rotor motor with thermal reset overload protection.
• Pre-wired with 120-volt power cords.

• High performance inline fans.
• Feature superior plastic or metal construction.
• Available in 10 or 12 inches sizes.
• Speed controllable.
• Vibration-free operation.
• Come with pre-installed cords from the manufacturer.
• Protected by a 1 year warranty.

• Designed to allow airflow in one direction.
• Minimum air leakage: exterior foam gaskets assure a tight seal.
• Aluminum spring-loaded backdraft damper blades.
• 20 gauge steel housing.
• Simple installation: entire assembly inserts into duct.
• Can be installed in any position: designed for vertical or horizontal mount.
• Specifically designed for use with ThermoFlo™ flexible ducting.
• Available in a range of sizes.

The Max-Fan® is the first fan that has been developed with a Computational Fluid Dynamics (CFD) program. CFDs are used for engineering aircraft propulsion engines. The perfectly designed 3D blades of the impeller and stator make this fan extremely powerful and energy efficient. Compared with other inline fans, the efficiency is 50% to 100% higher. 6 inch to 14 inch come pre-wired with an 8 foot 120 V power cord. Can-Fan® bring its innovation to market and sets a new standard for performance. The Max-Fan is a more powerful and efficient fan that takes less energy to run.

The Max-Fan® Pro Series is even more efficient and stronger than the original Max-Fan design. The Max-Fan Pro Series has a much more robust housing due to the fiberglass reinforced plastic compounds that meet all of the UL and CSA requirements. The fans have three control speeds for true performance. These fans run quieter than the Max-Fan. The fans come with the EZ Mount™ bracket for easy mounting.

The Atlas® 1 CO₂ features adjustable set point and elevation levels, a built-in self calibration function and an integrated photocell that enables operation in daytime hours only, when the plants need CO₂.

The Atlas® 2 features preset CO₂ control at 1,500 PPM. Simply plug in your CO₂ generator or regulator and you are ready to go.

The Atlas® 3 Controls and monitors CO₂ from 0 to 2,000 parts per million (PPM).

Compact and easy-to-use, the Atlas® 9 is a grower's dream. The 15 ft remote sensor allows you to measure the CO₂ levels of your garden exactly where you need to measure them.

CO₂ is scientifically proven to improve the performance of plants! The Ares® Series CO₂ generators provide a clean and efficient way to enrich your grow area with CO₂. Ares® Series CO₂ generators come with everything you need to get your CO₂ system started. Includes: CO₂ generator, AC power supply, hanging chain, ceiling hook, appropriate hose and regulator. All you need to provide is a gas source! 1.5 Amps/120 V/ 60 Hz.

Titan Controls® Apollo® Timers are the perfect timing solution for your hydro systems. They are easy to set to run your pumps, fans, etc. Can be configured in numerous timing schedules to meet the most demanding timing requirements. Heavy-duty construction. Easy to use and simple to operate. Enclosure resists dust, rust, and moisture.

• Greatly reduces duct noise.
• Does not impede airflow.
• Perfect for various environments, from residential to commercial.
• Suitable for installation in both new or existing ductwork.
• Available in a range of sizes.

• Easily reduce or increase duct diameter to suit requirements.
• Made with heavy-duty galvanized steel.
• Powder coated white.
• Designed for use with ThermoFlo™ flexible ducting.
• Available in a range of sizes.

• Allows multiple ventilation areas to be accessed by a single inline-fan source or for several fans to join a single exhaust.
• The "T" shape makes it ideal for right-angle joins in large spaces.
• Made with heavy-duty galvanized steel and powder coated white.
• Specifically designed to be used with ThermoFlo flexible ducting.
• Available in a range of sizes.

• Allows multiple ventilation areas to be accessed by a single inline-fan source or for several fans to join a single exhaust.
• The “Y” shape makes it useful in areas with tight access angles.
• Made with heavy-duty galvanized steel and powder coated white.
• Specifically designed to be used with ThermoFlo flexible ducting.
• Available in a range of sizes.

• Stainless steel clamps for attaching ducting.
• Make for clean and attractive duct connection.
• Simple to use.
• Available in a range of sizes.

• Connects two segments of round duct together.
• Ideal where added stability and sealing is required.
• Required when passing ventilation through a wall.
• Easily installed.
• Crafted with powder-coated heavy-duty galvanized steel.
• Designed for use with ThermoFlo flexible ducting.
• Available in a range of sizes.

• Flexible air ducting is expertly engineered to handle unconditioned air.
• Withstands high heat, high humidity, and excessive CFMs without any failure or fatigue.
• Manufactured with triple-foil laminate industrial-grade casing.
• Double-sealed core prevents punctures.
• Reinforced with “Rip-Stop” to eliminate tearing and unraveling.
• Industrial-grade woven fiberglass core reduces noise.
• Galvanized spring steel helix maintains duct shape and prevents rust.
• Duct components are flame resistant and self extinguishing.
• Oversized to fit easily onto connectors and fans.
• Allows more efficient air flow reducing energy consumption.
• Available in a range of sizes and custom lengths as a special order.

• Designed for low to moderate operating pressures.
• Economical solution for applications not requiring UL approval.
• Manufactured with 2-ply aluminum casing.
• Metal helix maintains duct shape.
• Fits easily onto connectors and fans.
• Convenient and quick installation will help reduce costs.
• 25-foot (7.6-meter) standard lengths that won’t unravel when cut.
• Includes two duct clamps.
• Available in a range of sizes.

• Designed for low to moderate operating pressures.
• Economical solution for applications not requiring UL approval.
• Manufactured with 2-ply aluminum casing and unique black core.
• Metal helix maintains duct shape.
• Fits easily onto connectors and fans.
• Convenient and quick installation will help reduce costs.
• 25-foot (7.6-meter) standard lengths that won’t unravel when cut.
• Includes two duct clamps.
• Available in a range of sizes.

• Economical solution for applications not requiring UL approval.
• Use for fresh air intake/exhaust on construction sites or temporary work areas.
• Manufactured with 2-ply aluminum / PVC casing.
• Very durable black PVC with UV inhibitors for sunlight exposure.
• Metal helix maintains duct shape.
• Fits easily onto connectors and fans.
• Convenient and quick installation will help reduce costs.
• 25’ standard lengths that won’t unravel when cut allows easy custom fitting.
• Maintenance free when installed according to manufacturer’s installation guidelines.
• Available in a range of sizes.

• Designed for use in all pressure cooling and heating systems.
• Provides economical means for handling misalignment between system components.
• Duct around obstacles where fabricated and fitted ducts are difficult and costly to install.
• Applications:
• Supply or return sections.
• Branch ducts and duct connections to or between mixing units, induction units, control or terminal units.
• Diffusion devices including light troffers.
• 25-foot (7.6 meter) standard lengths.
• Available in a range of sizes.

• Industrial-quality insulated flexible air duct.
• Manufactured tough for consumer and installer peace of mind.
• Features high-standard c-ETL-us / Can / ULC-S110-M86 / UL 181 approved cores.
• Consists of a three-ply polyester laminate, fiberglass reinforced scrim, and galvanized spring steel wire wrapped with fiberglass insulation.
• Provides an outstanding combination of strength and tear resistance.
• Insulation reduces heat loss and condensation.
• Heavy-duty fire-retardant black polyethylene vapor barrier adds extra durability.
• Ducting is marked approximately every foot for easy installation.
• Instructions included in each case.
• Made in Canada.
• 25-foot (7.6-meter) standard lengths.
• Available in a range of sizes.